Acnodes FES 2215 Bedienungsanleitung

14628 Central Ave,Chino, CA 91710tel:909.597.7588, fax:909.597.1939© Copyright 2013 Acnodes, Inc.All rights reserved. Product description and product

1-5 Front & Rear panel Front Panel Rear Panel

2-1 Front panel Pin Definition1. Power On/ Off Button2. Power Reset Button3. Power & HDD LED2-2 Rear Panel Pin Definition

2. COM 1 (DB-9):RS-232/ 422/ 485 [refer to P.17-18, No. 8 jumper setting]PINRS-232RS-422RS-4861DCD#TX+RTX+2RXDRX+Not Used3TXDTX-RTX-4DTR#RX-Not Used5G

2-3 Internal Pin Definition & Jumper Settings2-3.1 Main Board Top View

2-3.2 Main Board Pin Definition

2-3.3 Jumper Settings1. Clear CMONS Jumper (CLRCMOS1) [refer to P.13, No. 16]It allows you to clear the data in CMOS. To clear and reset the system pa

7. Panel Resolution Selection (12-pin JLVD_GPIO1) [refer to P.13, No. 29]8. SET COM Ports(10-pin SET_CM1,2) [refer to P.13, No. 1](10-pin SET_CM4,5,6)

(COM 1 Pin1 & Pin 9 Function Setting)ItemPin 1 FunctionConnector SET_COM1 Jumper SettingConfig. 1Provide ＋12V Power SourcePin 1 & Pin 3 short,

10. USB 2.0 Ports(4-pin USB 4,5) [refer to P.13, No. 11](4-pin USB6) [refer to P.13, No. 12]11. System Panel Header (9-pin PANEL 1) [refer to P. 13, N

13. Front Panel Audio Header (9-pin HD_AUDIO1) [refer to P.13, No. 25]14. DC 12V Power Connector (4-pin DC 12V1) [refer to P.13, No. 3]15. COM Port 4,

CopyrightThis publication contains information that is protected by copyright. No part of it may be reproduced inany form or by any means or used to m

16. Print Port Header (25-pin LPT1) [refer to P.13, No. 9]17. LVDS Con (40-pin LVDS1) [refer to P.13, No. 2]18. Output Power (4-pin SATA_PWR1) [refer

19. Digital I/O Header (10-pin JGPIO1) [refer to P.13, No. 13]20. Panel Brightness and Speaker Volume Control (7-pin BLT_VOL1) [refer to P.13, No. 21]

Chapter 3: UEFI Setup Utility3-1 IntroductionThis section explains how to use the UEFI SETUP UTILITY to configure yours system. The UEFI chip on themo

3-2 Main ScreenWhen you enter the UEFI SETUP UTILITY, the Main screen will appear and display the system overview.

3-3 Advanced ScreenIn this section, you may set the configurations for the following items: CPU Configuration, Chipset Configuration,Storage Configura

3-3.1 CPU ConfigurationIntel Hyper Threading TechnologyTo enable this feature, it requires a computer system with an Intel processor that supports Hyp

3-3.2 Chipset ConfigurationSet Panel Type byUse this to configure Set Panel Type.The Default value is [UEFI Setup].Panel Type SelectionUse this to sel

3-3.3 Storage ConfigurationOnboard SATAII ModeUse this to select SATA 2 mode. Configuration options: [IDE Mode], [AHCI Mode] and [D isabled].The defau

3-3.4 Super IO ConfigurationCOM 1 ConfigurationUse this to set parameters of COM1.COM 2 ConfigurationUse this to set parameters of COM2.COM 3 Configur

3-3.5 ACPI ConfigurationSuspend to RAMUse this item to select whether to auto-detect or disable the Suspend-to-RAM feature. Select [Auto]will enable t

14628 Central Ave,Chino, CA 91710tel:909.597.7588, fax:909.597.1939© Copyright 2013 Acnodes, Inc.All rights reserved. Product description and product

3-3.6 USB ConfigurationUSB 2.0 ControllerUse this item to enable or disable the use of USB 2.0 controller.Legacy USB SupportUse this option to select

3-3.7 Voltage ConfigurationDRMA VoltageUse this item to select DRMA Voltage. The default value is [Auto].

3-4 Hardware Health Event Monitoring ScreenIn this section, it allows you to monitor the status of the hardware on your system, including theparameter

3-5 Boot ScreenIn this section, it will display the available devices on your system for you to configure the boot settings andthe boot priority.Setup

3-6 Security ScreenIn this section, you may set, change or clear the supervisor/ user password for the system.

3-7 Exit ScreenSave Changes and ExitWhen you select this optino, it will pop-out the following message, “Save configuration changes andexit setup?” Se

Chapter 4: Installation Guide4-1. Memory Modules (SO-DIMM)Pipal 2215 provides two 240-pin DDR3 SO-DIMM slots.- It is NOT allowed to install a DDR or D

4-2. Expansion Slot (PCI Slot)There is 1 Mini-PCI-E expansion slot for FES 2215.PCI Slot: The PCI slot is used to install an expansion card that has 3

14628 Central Ave,Chino, CA 91710tel:909.597.7588, fax:909.597.1939© Copyright 2013 Acnodes, Inc.All rights reserved. Product description and pr

14628 Central Ave,Chino, CA 91710tel:909.597.7588, fax:909.597.1939© Copyright 2013 Acnodes, Inc.All rights reserved. Product description and product

1-2 Product SpecificationProcessor & Chipset Support Atom D2550 Dual-core 1.86 GHz low power Processor NM10 South Bridge ChipsetGraphic Engine

Front Panel Extend I/O Ports Power & HDD Led. Power & System, Power & Reset buttonRear Panel Extend I/O Ports Screw-Lock DC power input

1-3 System Block DiagramFES 2215

1-4 Mechanical DiagramsFES 2215